Programming

1. Press and hold the program button  until “PROG” shows in the display, followed by “ENTER CODE”.

2. Enter code 1, 2, 3 (first 3 product buttons). “PRODUCT” and “PROGRAM” show in the displays, followed by “SELECT PRODUCT’ and “-P 1-” (ex: NUG).

   Change Product Names

3. Use the up and down buttons to scroll through the 40 products, or press the desired product button.

4. Press the right arrow button and “NAME” shows in the left display and the product (ex: NUGGETS) shows in the right display.

5. Press “✓” button and the first letter in the name flashes. Press a product button and the flashing letter changes to the first letter under the product button that

   was pressed. For example, if product button one  is pressed, the flashing letter changes to an “A”. Press the same button again and the flashing letter changes to a “B”. Press it again and flashing letter changes to a “C”. Once the desired letter displays, press the right arrow button to continue to next letter and repeat the procedure. Press and hold the right “X” button to exit Program Mode, or press the right arrow button to continue on to “COOK TIME”.

   Assign Button

6. Press the right arrow button until “ASSIGN BTN” shows in the display, along with the product (ex: NUGGETS). If this product already has a product button assigned to it, that LED will be lit. To assign other product buttons to that product, press and hold the product button for 3 seconds and that LED stays lit. To remove a product from a button, press and hold the product button with a lit LED and the LED goes out.

   Change Times & Temperature

7. Press the right arrow button until “COOK TIME” shows in the display, and then use the product buttons, or the up arrow and down arrow buttons, to change the time in minutes and seconds, to a maximum of 59:59.

8. Press the right arrow button and “TEMP” shows in the display, along with the preset temperature on the right side of the display. Press the product buttons, or the up arrow and down arrow buttons, to change the temperature. The temperature range is 190°F (88°C) to 375°F (191°C).

   Cook ID Change

9. Press the right arrow button until “COOK ID” shows in the display along with the product ID. For example, NUG would be the ID for nuggets. Use the product buttons, or the up arrow and down arrow buttons, to change the ID.

   Alarms (1 & 2)

10. Press the right arrow button until “ALRM 1” shows in the left display, and an alarm time in the right display. Press the product buttons, or the up and down arrow buttons, to set an alarm. Ex., If a Cook Cycle was set at 3 minutes, and an alarm was to go off after 30 seconds into the Cook Cycle, “2:30” would be set in the display at this time. When the timer counts down to 2:30 the alarm sounds. After alarm time is set, press the right arrow button and “ALRM 2” displays, and a second alarm can be programmed.

    Quality Timer (Hold Time)

11. Press the right arrow button until “QUAL TMR” shows in the display along with the preset holding time. Press the product buttons or the up and down arrow buttons to adjust holding time, up to 2 hours: 59 minutes.

    Filter Tracking

12. Set the filter tracking:

    1. Global Filter Tracking - Include In Filter Count

       Press the right arrow button until “INCL IN FLTR CNT” flashes in display along with “YES” or “NO”. Using the up or down arrow buttons, change the display to “YES” if that product’s Cook Cycles are to be counted as part of the recommended filter process. Set to “NO” if it is not to be included.

    2. Mixed Filter Tracking - Filter After “X” Number Of Loads

       Press the right arrow button until “FILTER AFTER ...” flashes in the left display, and the number of cook cycles between filters shows in the right display. Press the product buttons or the up and down arrow buttons to change this value of 0 to 99 loads. This needs set for each product.

       Load Compensation

13. Press the right arrow button until “LD COMP” shows in the display along with the load compensation value. This automatically adjusts the time to account for the size and temperature of the cooking load. Press the product buttons of the up and down arrow buttons to change this value of 0 to 20.

    Load Compensation Reference

14. Press the right arrow button until “LCMP REF” shows in the display along with the load compensation average temperature (if load compensation is set to “OFF”, then “_ _ _” displays and setting cannot be programmed). This is the average cooking temperature for each product. The timer speeds up at temperatures above this setting and slows down at temperatures below this setting. Press the product button or the up and down arrow buttons to change this value.

    Full Heat

15. Press the right arrow button until “FULL HT” shows in the display along with the full heat value in seconds, which means the heat is on as soon as a timer button is pressed, for the programmed length of time. Press the product button or the up and down arrow buttons to change this value of 0 to 90 seconds.

    PC Factor

16. Press the right arrow button until “PC FCTR” shows in the display along with the proportional temperature, which helps to keep the oil from over-shooting the set- point temperature. Press the product button or the up and down arrow buttons to change this value of 0 to 50 degrees.