Special Programming

Press the plus or minus button to select either FAH- RENHEIT ( F) or CELSIUS ( C).

Press the plus or minus button to scroll through a list of languages. Press a language to select. NOTE: Sup- ports the Russian language for v1.60 or higher.

Press the hold-> button for three seconds to reset the controls to factory defaults.

Press the plus or minus buttons to enable or disable the OPS or QPM wireless communications for this con- trol. Requires an optional radio module.

Press the plus or minus button to select:

Press the plus or minus button to adjust the volume (loudness) of the speaker between 1-10, then press the TEST button to test the loudness.

Press the plus or minus button to adjust the frequency (tone) setting, then press the TEST button to test the tone.

Press the plus or minus button to select either the SO- LID or LIQUID melt mode heating cycle.

Press the plus or minus button to select either YES or NO to specify whether an automatic polish operation should be performed as part of the normal morning Start-Up process.

Press the plus or minus button to select a default cook menu that displays after exiting the melt mode.

Press the plus or minus button to navigate through cook menu options. Refer to Display Options section of the Operator Manual.

• SELECT - to begin preheating when a cook menu button is pressed.
• COOK - to begin the cook cycle immediately.

Press the plus or minus button to select the default cook menu to display after each cook cycle completes.

Press the plus or minus button to select a time in minutes. When a selected product begins preheating, and the drop temperature is reached but a cook cycle is not started, after X minutes the control automatically returns to a cook menu.

If Auto-Menu feature is enabled, press the plus or minus button to select a default cook menu that displays after the timer times out.

Press the plus or minus button to select:

• YES - to step through all the times first, then all temps and then all pressures.
• NO - to step through Time1, Temp1, Pressure1 and then Time2, Temp2, Pressure2, etc.

Press the plus or minus button to select one of three options:

• NONE - Dispose by draining into a disposal cart or shuttle.
• REAR HOSE - Dispose by pumping through the rear plumbing connection.
• FRONT HOSE - Dispose by pumping through the front hose connection by pressing and holding the button.

NOTE: The optional front hose kit must be installed and enabled by a field technician or at the factory in Tech Mode screen T-4A before it displays in Special Programming SP-17.

Press the plus or minus button to select one of three options:

• NONE - Dispose by draining into a disposal cart or shuttle.
• REAR HOSE - Dispose by pumping through the rear plumbing connection.
• FRONT HOSE - Dispose by pumping through the front hose connection by pressing and holding the button.

NOTE: The optional front hose kit must be installed and enabled by a field technician or at the factory in Tech Mode screen T-4A before it displays in Special Programming SP-17.

Set to match tank full signal logic of your bulk disposal tank:

• NONE - Disables tank full signal.
• 24V=FULL - 24V signal on DTF wires means tank is full (do not pump). No signal means it is OK to pump .24V=OK - 24V signal on DTF wires means it is OK to pump. No signal means the tank is full (do not pump).

Set to match tank full signal logic of your bulk disposal tank:

• NONE - Disables tank full signal.
• 24V=FULL - 24V signal on DTF wires means tank is full (do not pump). No signal means it is OK to pump .24V=OK - 24V signal on DTF wires means it is OK to pump. No signal means the tank is full (do not pump).

Press the plus or minus button to select either YES, NO, or YES+BSV to indicate if a bulk oil supply is available for refilling the ATO oil tank and vat with fresh oil.

Press the plus or minus button to select either YES, NO, or YES+BSV to indicate if a bulk oil supply is available for refilling the ATO oil tank and vat with fresh oil.

Press the plus or minus button to select YES or NO to display the live pressure reading (in PSI) on the bottom line of the control board during the cook cycle for pressure fryers only.

Press the plus or minus button to select YES or NO to display the live pressure reading (in PSI) on the bottom line of the control board during the cook cycle for pressure fryers only.

Provides access to change the Manager password code, which is defaulted to 123 from the factory. The manager password code is used to access modes such as Product, Cook, Special Programming, etc.

Provides access to change the Manager password code, which is defaulted to 123 from the factory. The manager password code is used to access modes such as Product, Cook, Special Programming, etc.

Provides access to change the Reset Usage password code, which is defaulted to 123 from the factory. The Reset Usage password code is used to access the usage statistics, it does not grant any programming privileges.

Provides access to change the Reset Usage password code, which is defaulted to 123 from the factory. The Reset Usage password code is used to access the usage statistics, it does not grant any programming privileges.

The Clean-Out function supports two different water based clean-out modes, Heated and Cold-Soak. Heated is heated and timed while Cold-Soak is unheated and not timed. NOTE: KFC software is hard-coded for Cold-Soak only, it cannot be changed.

If Heated mode is selected in the SP-22 menu, operators may select a temperature between 40°F – 195°F with which to heat the water. If Cold-Soak mode is selected in the SP-22 menu, this setting displays Cold-Soak and can not be changed. NOTE: Higher temperatures require Personal Protective Equipment (PPE) to prevent burns.