Info Mode Menu Overview

Displays the history of the previous 25 error codes starting with the most recent code first. Codes includes the date and time that the error occurred.

Displays information about the most recent cook cycle, including total cook time, early stops, if timer is left beeping too long and min./max./avg. temperatures.

Displays operating statistics for each of the past seven days, including hours on, cook cycles, number of filters, etc.

Displays the summation of the operating statistics for the previous 7 days of operation, NOT including today.

Displays ongoing accumulations of operating statistics, which continues to accumulate until a manual reset is performed. To reset (requires pass- word), navigate to the bottom of the list.

Displays a summary of operating statistics for the current batch of oil, NOT including today.

When a dispose or clean-out operation or both are performed, the oil statistics are copied to the Prev Oil statistics and then This Oil statistics are reset.

Displays the operating statistics accumulated during the previous batch of oi.

When a dispose or clean-out operation or both are performed, the accumulated oil statistics are copied to the Prev Oil Stats record.

Displays history of Activity Log events as:

• On/Off

• Start/Stop Cook

• Filter

• Pan Removed or Replaced

Displays live temperature reading for the CPU (controller), software version, and software part number.

Displays live readings for main oil, level probe, and the bottom of vat temperature.

• ✓ - Signal present

• - - No signal present

• A - Power Switch

• H - High Limit

• D - Drain Switch Jumper

• S - Power Switch Interlock

• F - Fan Switch Jumper

• ✓ - Signal present

• - - No signal present

• A - Power Switch

• H1 - High Limit, Lower

• H2 - High Limit, Upper

• B - Circuit Breaker (or CB Jumper)

• S - Power Switch Interlock

• ✓ - Signal present

• - - No signal present

• 24dc - 24 DC Supply

• Pan - Filter Drain Pan

• *Lid - Lid Liner Pin:

  • Lid Liner Pin shows OK if pin is down

  • Lid Liner Pin shows PR when pin is raised (under pressure)

• 24ac - Transformer OK

• Pan - Filter Drain Pan

• 24ac ✓ - 24 VAC OK

• Pan ✓ - Filter Drain Pan present

• ✓ - Signal present

• - - No signal present

• DTF - Discard Tank Full

• FULL - Discard tank is full and cannot dispose to it

• OK - Discard tank not full, okay to dispose

Displays reading from the pressure transducer as:

• OK - Safe to open lid (not under pressure)

• PR - Lid under pressure, cannot open

• No Pressure Inputs

Displays pump pressure reading if optional transducer is installed in plumbing manifold as:

• * - On

• - - Off

otherwise displays NO SENSOR.

• * - On

• - - Off

• Pri - Primary Contactor

• Ht - Heat (regulating) Contactor

• Pr - Pressure Solenoid

• BSV - Bulk Supply Valve (optional)

• * - On

• - - Off

• Pri - Primary Contactor

• Ht/Ht1 - Main Heat (regulating) Contactor

• Ht2 (Open Fryer only) - Heat Contractor for upper heaters

• Pr (Pressure Fryer only) - Pressure Solenoid

Displays heater on/off status and associated amp draws.

Open Fryer:

• H2 - upper heater

• H1 - lower heater

Pressure Fryer:

• Ht - single heater with three amp readings

• Par - Partially open

• Stp - Forced Stop

• Opn - Fully Open

• Cls - Fully Closed

• ► - The current state of the drain valve

• At - indicates the drain valve position

  • 0 - Fully Closed

  • 20+ - Fully Open

Displays in the lower right with the current port position as:

• No Selector Valve - unit is not equipped with a Bulk Oil System

  Displays in the lower left with the activity of the valve as:

• E=001 - Encoder Position

• STPD - Stopped

• FWD - Forward

• REV - Reverse

• * - On

• - - Off

• Fltr - Filter Pump

• ATO - Top Off Pump

• Bulk - Bulk oil Supply

Displays analog input readings directly from ADC chip displayed as volts and as ADC counts (bits). Use the up and down arrows to step through available inputs.

Displays the status and size of the controls internal microSD storage memory as:

• ✓ - Memory OK

• X - Memory problem

If installed, displays the status and size of the USB flash drive as:

• ✓ - Flash Drive OK

• X - Flash Drive not present or drive error

• hcc - 16 is normal if no USB drive is plugged in

Scroll down to see flash drive volume name.

Displays number of cycles on the heat contactor.

Displays current filter coordination information and filter communications statistics.

• LVL - Levels:

  • FULL

  • LOW

  • Displays when an assessment is not possible

• Delta - Displays the temperature difference between the main probe and the level probe.

• Cnt - Count shows how many ATO pulses have been generated in the current top-off attempt.

• LVL (Levels):

  • FULL

  • LOW

  • --- Displays when an assessment is not possible

• Delta - Displays the temperature difference between the main probe and the level probe.

• Dly - Delay shows the number of seconds before the next ATO pulse is allowed. Use the lower, right button to toggle to Cnt.

• Cnt - Count shows how many ATO pulses have been generated in the current top-off attempt. Use the lower, right button to toggle to Dly.

If OPS and QPM are enabled, displays the ZigBee radio status as:

• ✓ - Good communication in past 15 seconds

• - - No good message for 15 to 60 seconds

• X - No good message for 60+ seconds Press the down arrow to view:

• Join status

• Channel number

• PAN ID

• Radio ID

• Reset (un-join) button